Water · Kc

Crop coefficient Kc

A factor that scales reference evapotranspiration to one crop at one growth stage.

Multiply the reference evapotranspiration (ET₀) by the crop coefficient (Kc) to get the crop water need (ETc = Kc × ET₀). Kc varies through the season: it is low at emergence, peaks at full canopy and falls again as the crop matures.

Kc values by crop and growth stage (FAO-56)

CropInitialDevelop.Mid-seasonLate seasonNotes
Wheat 0.30 0.30–1.15 1.15 0.25–0.40 High mid-season when full canopy
Maize 0.30 0.30–1.20 1.20 0.35–0.60 Very high at silking/tasselling
Potato 0.50 0.50–1.15 1.15 0.75–0.85 Stays relatively high through senescence
Onion 0.50 0.50–1.05 1.05 0.75–0.85 Sensitive to water stress throughout
Tomato (field) 0.60 0.60–1.15 1.15 0.70–0.90 Protected cropping values differ

Source: FAO-56 Table 12. Mid-season values are peak Kc — used for maximum crop water demand calculation. Adjust for local humidity and wind speed if significantly different from standard FAO-56 conditions.

How Kc changes through the season

Kc is not a fixed number — it rises through crop development as leaf area increases, reaches a peak at full canopy (mid-season), and then falls as the crop matures and senescence reduces transpiration. The transition is gradual, not stepped. FAO-56 ↗ provides standard Kc curves for each crop, with methods to interpolate Kc on any given day given the crop development stage.

In practice, the most accurate approach for UK field crops is to use growing degree day accumulation to track growth stage and select the corresponding Kc. AHDB IrriGuide ↗ automates this for potato and vegetable crops in UK growing regions. See the growing degree days entry for how heat accumulation is calculated from daily maximum and minimum temperatures.

The ETc calculation in practice

ETc (crop evapotranspiration) = ET₀ × Kc. Once you have ETc, subtract effective rainfall to get the irrigation deficit: deficit (mm) = ETc − effective rainfall. When the deficit exceeds a threshold (typically 25 mm for potatoes, 35–50 mm for cereals), irrigation is triggered. The threshold varies by crop sensitivity, soil type and available water capacity. See the irrigation scheduling guide for how this calculation drives irrigation timing and volumes for UK field crops. The effective rainfall glossary entry explains which part of total rainfall is available to the crop.

Frequently asked questions

How is Kc used to calculate daily crop water demand?
The formula is: ETc (mm/day) = ET₀ × Kc, where ET₀ is the reference evapotranspiration from weather data (temperature, humidity, wind, solar radiation) and Kc is the crop coefficient for the current growth stage. FAO-56 ↗ (the standard reference) provides Kc values for over 60 crops and growth stage definitions. For example: wheat at mid-season (Kc = 1.15) on a day when ET₀ = 4 mm/day requires 4 × 1.15 = 4.6 mm/day of water. Over a 7-day period without rain: 32.2 mm of crop water use. See the ET₀ glossary entry for how ET₀ is calculated.
What does a Kc of less than 1 vs. greater than 1 mean?
The reference ET₀ is defined for a short green grass surface fully covering the ground with no water stress. A crop Kc <1 means that crop uses less water than the reference grass at that growth stage — typically at early emergence when canopy cover is partial. A Kc >1 means the crop uses more water than the reference grass — typically at peak canopy when leaf area, crop height and aerodynamic roughness all exceed the grass reference. Maize at full canopy (Kc 1.20) uses 20% more water per day than the reference grass surface would. AHDB irrigation guidance ↗ applies Kc values to UK crop water budgeting.
How do I know what growth stage my crop is at for the right Kc?
FAO-56 divides the crop season into four stages: initial (emergence to ~10% canopy cover), crop development (10% to full canopy), mid-season (full canopy to start of maturation), and late season (maturation to harvest). The duration of each stage in days is calibrated to the specific crop and climate. In the UK, visual crop assessment using crop growth stage scales (e.g. Zadoks for cereals) combined with growing degree day accumulation provides the most accurate stage timing for Kc selection. Commercial irrigation decision support systems automate this — AHDB IrriGuide ↗ is the primary UK tool.
Does Kc change with irrigation method or crop density?
Yes — FAO-56 provides adjustments to the standard Kc for: climate (humidity and wind speed affect mid-season Kc); canopy height (taller crops have higher aerodynamic resistance); and partial wetting (drip irrigation wets only part of the soil surface, reducing soil evaporation and therefore requiring a lower effective Kc). These adjustments are significant for precision irrigation scheduling. For UK field crops under overhead irrigation or rain-guns, the standard FAO-56 Kc values are generally appropriate. See the irrigation scheduling guide for how Kc is applied in practice for UK field crops.
Where can I find ET₀ data for the UK?
UK ET₀ data sources: Open-Meteo ↗ provides historical and forecast ET₀ via a free API (commercial use requires a paid plan — see FarmTheGuide notes on the proxy requirement). Met Office UK climate averages ↗ give long-run monthly ET₀ by region, useful for seasonal planning. AHDB IrriGuide ↗ provides weekly ET₀ and crop water use estimates for key UK potato and vegetable growing regions. The reference evapotranspiration glossary entry explains the FAO Penman-Monteith calculation.