Soil

Soil texture

The proportions of sand, silt and clay in a soil.

Texture determines water-holding capacity, drainage, workability and nutrient retention. Sandy soils drain fast and warm quickly but hold little water. Clay soils retain water and nutrients but are slow to drain and hard to cultivate when wet. Loams — balanced sand/silt/clay — are generally easiest to manage.

Soil texture classes and their properties

Texture classSandSiltClayDrainageWorkabilityWater holding
Sand >85% <15% <10% Very fast Very easy Very low
Sandy loam 70–85% <30% <15% Fast Easy Low
Loam 25–52% 28–50% 7–27% Good Good Medium
Silt loam <50% 50–88% <27% Moderate Good High
Clay loam <45% <53% 27–40% Slow Difficult High
Clay <45% <40% >40% Very slow Very difficult Very high

Why sand, silt and clay behave differently

The three mineral fractions differ in particle size, and particle size drives almost every physical property of soil. Sand particles (0.05–2 mm) are coarse — they create large pores between them, allowing rapid water drainage and gas exchange but holding little water. Clay particles (<0.002 mm) are microscopically thin plates with enormous surface area relative to their volume; they carry negative electrical charges that attract and hold water molecules and positively charged nutrient ions (calcium, magnesium, potassium). Silt particles (0.002–0.05 mm) are intermediate and contribute to silky soil texture.

When clay particles are well-aggregated — held together by organic matter, fungal hyphae and glomalin — the soil has both large pores (for drainage) and internal small pores (for water retention). This is the structural ideal. Poor management (compaction, over-tillage, bare soil) destroys aggregates and creates the characteristic problems of clay: wet and plastic in winter, hard and cracked in drought. The soil organic matter guide covers how organic inputs and tillage management protect soil structure.

Texture, pH and liming

Clay soils require substantially more lime than sandy soils to achieve the same pH change because their high cation exchange capacity (CEC) resists change — a property called buffer capacity. A sandy loam soil at pH 5.8 might need 2 t/ha ground limestone to reach pH 6.5; a clay soil at the same starting pH might need 6–8 t/ha for the same change. Never apply lime without a soil test that provides a buffer capacity measurement. See the liming glossary entry and the soil pH management guide for lime rate calculation methodology.

Texture and irrigation scheduling

Soil texture determines the total available water (TAW) that a soil can hold for plant use — the difference between field capacity and permanent wilting point. Sandy soils have a TAW of approximately 60–90 mm/m depth; clay soils can hold 120–180 mm/m. Knowing your texture class is the foundation of soil moisture deficit (SMD) calculations in irrigation scheduling. Use the AHDB irrigation scheduling tools ↗ — they require a soil texture input to calculate SMD thresholds.

Frequently asked questions

How do I find out my soil texture?
The simplest field method is the hand texture test: moisten a small amount of soil and work it between your fingers and palm. Sandy soil feels gritty; silty soil feels smooth and silky (like flour); clay soil is sticky and plastic — it can be moulded and threads out when rolled. Professional texture classification uses laboratory particle size analysis. Many soil testing laboratories include texture class in their standard report. AHDB soil texture guidance ↗ provides a full description of the field hand texture method with photographs.
Why does soil texture affect liming rates?
Clay soils have a much higher buffer capacity than sandy soils — they resist pH change because of cation exchange sites on clay particles and organic matter. This means clay soils need more lime (more tonnes per hectare) to achieve the same pH increase as a sandy soil. The lime requirement calculation in RB209 ↗ and the PLANET tool ↗ incorporates soil texture to calculate the correct lime rate. See the liming glossary entry for how lime requirement is calculated.
How does texture affect workability and cultivation timing?
Clay soils have a narrow workability window — they must be cultivated when moisture content is at or below the plastic limit. Working clay soils too wet causes compaction and smearing; too dry causes hard clods. Sandy soils have a much wider window but dry out faster. Knowing your texture helps predict workability from weather data: after 15 mm of rain, a sandy loam may be workable again in 1–2 days; a clay loam may take a week or more. AHDB soil management guidance ↗ covers workability and cultivation decisions by texture class.
Does soil texture change over time?
The mineral particle proportions (sand, silt, clay) that define soil texture do not change over agricultural timescales — texture is a fixed property of the soil. However, soil structure (how those particles are arranged and aggregated) can change dramatically with management: tillage, organic matter inputs, cover crops and biological activity all improve structure. The distinction between texture (fixed) and structure (manageable) is important when considering soil health interventions. See the soil organic matter guide for how management affects structure.
What is the best soil texture for arable farming?
Loam and sandy loam soils are generally considered easiest to manage for arable farming — they combine reasonable water retention, good drainage, ease of cultivation and structural resilience. Silty soils can cap (form surface crusts) and are prone to compaction, but are often very fertile. Heavy clays support high yields but require precise management of workability windows. Very sandy soils need supplemental irrigation and have low nutrient retention. Most soils benefit from organic matter additions regardless of texture class — see the soil organic matter guide.