Harvest 5 min read Wheat · Barley

Harvest Management Cereals

Harvest Management Cereals guide.

When is the crop ready to combine?

Harvest readiness is driven by grain moisture content (MC), not calendar date. Typical combining windows open when grain MC drops below 20 %. At 22–25 %, threshing is poor and drum losses are high. Below 14 %, grain is in ideal storage condition but brittle at the cutterbar.

The practical combining range is 15–19 % MC. This balances throughput, grain quality and drying cost. Use a handheld moisture meter (Dickey-John ↗ or similar) in at least five field locations to get a representative reading before committing the combine.

≤ 14.0 % Safe for long-term storage
14.1–16.0 % Short-term storage, dry promptly
16.1–18.0 % Dry within 24–48 hours
> 18.0 % Dry immediately — heating risk

Combine settings

The combine has three main control points: threshing (drum/rotor speed and concave clearance), separation (rotor speed and concave openings on rotary machines), and cleaning (fan speed, upper and lower sieve apertures).

A conservative starting point for winter wheat (16–18 % MC): drum speed 900–1,000 rpm, concave clearance 12–14 mm, fan speed 7–8 m/s. Adjust based on crop density, tangled straw and the grain pan load. CLAAS Combine Advisor ↗ provides model-specific guided setup.

Checking losses

Walk 20 m behind the combine immediately after the first pass. Count grains per m² on the stubble. The industry threshold is 1 grain per m² = approximately 1 kg/ha of losses. At 15 kg/ha loss on a 300 ha wheat field, that is over £30,000 at £200/t. UMN Extension — Combine adjustments ↗ covers a systematic loss audit protocol.

Grain quality monitoring at intake

For each intake load, record: moisture content (%), specific weight (kg/hl), and — for milling wheat — Hagberg falling number. NABIM ↗ defines contract thresholds: typically specific weight ≥ 76 kg/hl, Hagberg ≥ 250 s, and protein ≥ 13 % for Group 1 milling wheat.

Segregate intake by moisture band to optimise drying. Grain at 16–17 % is much cheaper to dry than grain at 20 %+ — mixing them wastes energy. Use batch or continuous-flow drying strategically: AHDB grain drying cost guide ↗ has a full cost model.

Drying and cooling

Dry wheat to 14 % and barley to 15 % for safe long-term storage. After drying, cool the grain to below 15 °C within 2 weeks, and to 5 °C for over-winter storage. Cooling is a key tool in mycotoxin and insect management. The AHDB Grain Storage Guide ↗ and FAO grain post-harvest guide ↗ both provide detailed protocols.

Frequently asked questions

At what moisture content should I harvest wheat?
Combining is typically practical at 16–20 % grain moisture, depending on the market destination. AHDB grain storage guide ↗ defines 14 % as the safe storage moisture for wheat and 15 % for barley. Grain above these thresholds must be dried.
How do I optimise combine settings for wheat?
The three main settings are drum/rotor speed, concave clearance and fan speed. For wheat, a starting point is: rotor/drum 900–1100 rpm, concave 10–16 mm, fan 6–8 m/s. CLAAS Combine Advisor ↗ and John Deere IntelliCruise ↗ both offer automated setting optimisation based on yield data.
What is the cost of drying grain per point of moisture?
The energy cost to remove one percentage point of moisture from one tonne of grain is approximately 0.02–0.03 GJ, equivalent to £1.50–£3.00/t per point at current gas/propane prices. AHDB grain drying costs guide ↗ provides a full cost model including fixed costs for dryer depreciation.
How do I monitor grain temperature in store?
Temperature cables at multiple heights give an early warning of hotspots. Grain above 25 °C in store requires immediate ventilation. The AHDB Guide to Grain Storage ↗ provides a complete temperature and ventilation management protocol. Aim for 5 °C for long-term storage.
What grain samples do I need to take at intake?
Take representative samples from each intake load using a spear sampler. Test moisture content, specific weight (kg/hl) and Hagberg falling number (for milling wheat). Grain Lab UK ↗ and NABIM ↗ define the quality thresholds for milling and feed wheat contracts.
How do I reduce combine losses?
Walk behind the combine on the first pass and check for grain on the stubble. High losses are usually either at the front (reel speed too fast, cutterbar height wrong) or the rear (sieves too open, fan too strong). New Holland combining tips ↗ and UMN Extension — Combine adjustments ↗ both cover the systematic approach.