Liming materials: neutralising value, speed and cost
Step-by-step liming programme
- 1
Test soil pH and identify target pH before calculating lime requirement
Soil pH testing is the foundation of liming decisions. Test frequency: every 4–5 years on arable land, more frequently on lighter soils where pH can change faster. Use a UKAS-accredited laboratory — pH meter reading from a soil-water slurry (1:2.5 ratio) is the standard UK method. Target pH by crop: most combinable crops (wheat, barley, OSR) target pH 6.5–7.0 on mineral soils; maize targets pH 6.5–7.0; potatoes prefer pH 5.5–6.0 (higher scab risk above pH 6.5); onions target pH 6.5–7.0; cover crops as preceding crops target pH 6.5–7.0. On peaty and organic soils, the target pH is higher (6.5–7.0) because pH measurement in organic matter underestimates the effective acidity. Lime requirement is not calculated from pH alone — both pH and soil type (buffer capacity) determine the lime needed to raise pH by one unit.
- 2
Select the appropriate liming material based on neutralising value, particle size and magnesium status
Neutralising value (NV, expressed as % calcium carbonate equivalent, CCE) is the most important single parameter for liming material selection — it determines how much lime is needed per tonne to deliver a given neutralisation effect. Fineness of grinding determines speed of reaction: finer particles react faster (useful for rapid correction) while coarser particles provide slower, longer-lasting pH maintenance. UK lime regulations set minimum NV and fineness standards for materials sold as agricultural lime. On soils with low Mg index (index 0–1), dolomitic limestone provides a combined pH correction and Mg supply in a single application — typically 15–20 kg MgO per tonne of dolomitic limestone. Where Mg index is adequate, ground limestone is preferred as it does not supply unwanted excess Mg on already Mg-adequate soils.
- 3
Calculate lime rate from soil pH, target pH, soil texture and buffer capacity
The lime requirement (in tonnes/ha) to raise soil pH from current to target is calculated using: (1) pH deficit (target pH minus current pH); (2) soil texture and organic matter content (heavy clays and high-OM soils have high buffer capacity and require more lime per unit of pH increase); (3) NV of the selected lime material. AHDB RB209 Section 3 provides lime requirement tables by soil type. Typical application rates to raise pH 1.0 unit: light sandy soils 2–3 t/ha ground limestone; medium loam 3–5 t/ha; heavy clay 5–8 t/ha; peat 8–15 t/ha. Maximum single application: 7.5 t/ha for most liming materials on mineral soils — larger rates take longer to fully incorporate and can create pH stratification in the topsoil. If the correction needed exceeds 7.5 t/ha, split the application across two years.
- 4
Time lime application to allow reaction before the sensitive crop phase
Lime reacts slowly in soil — ground limestone takes 1–2 years to achieve its full pH correction effect. This means lime must be applied before the most acid-sensitive crop or management event in the rotation. The ideal timing is directly after harvest of the previous crop, allowing autumn and winter rainfall to react with the lime before spring drilling of a pH-sensitive following crop. Autumn application before maize or potato on acid soils is particularly important. Avoid applying lime immediately before drilling — the sudden pH shift can affect fertiliser N availability and may affect some herbicide performance. Avoid applying lime and phosphate fertiliser simultaneously — calcium from lime can react with phosphate fertiliser to form insoluble calcium phosphate, reducing P availability. Leave a gap of at least 3 months between lime and phosphate applications on the same field.
- 5
Record all lime applications and retest soil pH every 4–5 years to track progress
All lime applications must be recorded in the farm's nutrient register — product, NV, rate applied, date, field and application method. This is required under NVZ regulations for farms in NVZs, under SFI scheme conditions, and is good farming practice for all farms. Retesting pH every 4–5 years confirms whether the target has been achieved and whether maintenance liming is needed. On soils that naturally acidify quickly (high rainfall, intensive cereals cropping, ammonium-based fertilisers, acid-forming break crops like potatoes) — annual pH monitoring is advisable after an initial correction, especially if further acid inputs are planned. Soil pH testing as part of a complete soil analysis (P, K, Mg indices alongside pH) allows integrated nutrient management planning in a single test round.
Soil pH and the wider nutrient interaction
Soil pH is the single most powerful lever for improving nutrient availability across the full soil chemistry spectrum. Correcting soil acidity improves the efficiency of all other nutrient applications — phosphate fixed at low pH becomes available; sulphur cycling by soil bacteria accelerates; nitrogen mineralisation from organic matter increases. See the soil pH glossary entry for the full nutrient availability pH chart, and the magnesium glossary entry and boron glossary entry for the specific pH interactions of two commonly deficient nutrients. The wheat nutrition management guide and OSR nutrition management guide both include soil pH considerations for their respective crop nutrition programmes.