Wheat nutrient requirements: key parameters
Step-by-step wheat nutrition programme
- 1
Establish yield target and soil nitrogen supply (SNS) class before calculating N rate
The AHDB RB209 Nutrient Management Guide for Arable Crops is the UK industry standard for N rate calculation. The process: (1) Set a realistic yield target for the field based on 5-year average ± expected season; (2) Determine SNS class (0–6) from soil type, previous crop and organic manure history; (3) Apply the RB209 N rate table for the relevant SNS class and yield target. Typical outputs for milling wheat on medium soil: 220–240 kg N/ha; for feed wheat: 180–210 kg N/ha. The SNS adjustment reduces N rate on high-organic-matter soils, following legume break crops or after a period of organic manure applications. Never apply more than 250 kg N/ha total in any one year on any crop under NVZ rules.
- 2
Plan P and K applications based on soil index and offtake
Phosphorus and potassium in wheat are managed on an index system (RB209 indices 0–4+). At index 2, apply maintenance dressings to replace crop offtake (P₂O₅ offtake ≈ 5–7 kg/t grain; K₂O offtake ≈ 5–6 kg/t grain for straw retained, 10–12 kg/t straw removed). At index 0–1, build-up applications are required in addition to maintenance. At index 3–4, P and K can often be omitted for 1–2 seasons. Soil testing every 3–4 years at consistent depth (0–15 cm) tracks index changes. Where P index is below 2 on a field with high yield potential, this is often a significant constraint on achieving maximum yield even where N is adequate. Record all applications in a field nutrient register.
- 3
Include sulphur at every N application split
Sulphur should be applied at the first and second N splits — not the third, as late S applied post-GS32 contributes little to yield and risks increasing grain sulphur to levels that affect baking quality in milling wheat. The sulphur requirement is approximately 40 kg SO₃/ha for most UK wheat crops, rising to 60+ kg SO₃/ha on light soils, high-yield targets (>9 t/ha) or following very high rainfall over winter (which leaches sulphate). Products: ammonium sulphate in compound N+S fertilisers; sulphate of potash for K+S; granular gypsum (calcium sulphate) as a slow-release option. Elemental sulphur is not immediately plant-available and should be applied in autumn or early spring to allow oxidation before demand peaks.
- 4
Calibrate and time nitrogen applications within the recommendation window
The split nitrogen programme is the standard UK approach for wheat: first N (Feb–early Mar) at GS21–GS25 using a smaller dose (40–60 kg N/ha) to stimulate tillering and early growth; second N (late Mar–Apr) at GS25–GS30 at the largest dose (80–100 kg N/ha) to support stem elongation and ear initiation; third N (Apr–May) at GS31–GS37 for flag leaf protection and grain protein support. Milling wheat may receive a fourth, late application to target protein specification. Timing is critical — applications too early in cold, wet conditions on heavy soils risk losses through denitrification or surface run-off. Calibrate spreader output before each application and check against manufacturer settings for the product batch.
- 5
Monitor crop response and adjust at each timing decision point
Canopy assessment between N splits is important for adjusting the programme: a thin, pale crop may need the second split moved forward; a very dense, dark green canopy may benefit from a reduced second split to avoid excessive lodging risk at GS30–31. Leaf colour charts and canopy sensors (Yara N-Sensor, GreenSeeker, crop circle sensors) can provide objective N-status information at each decision point. AHDB research consistently shows that crops with canopy sizes between 750–900 green area index (GAI) at GS30–32 achieve maximum yield with minimum lodging risk. Where canopy exceeds this range, reducing the final N split is preferable to applying a PGR alone. See the precision nitrogen management guide for technology-assisted decision support approaches.
Organic manures and nutrient management planning
Organic manures — farmyard manure, slurry, digestate, compost — are valuable nutrient sources that can significantly offset the need for inorganic fertiliser. The key is accurate nutrient content measurement (laboratory analysis preferred over handbook values) and calculation of the available N in the year of application (typically 25–40% of total N for FYM, 60–75% for slurry injected). All significant organic manure applications must be recorded in the farm nutrient register and factored into the nutrient budget before inorganic inputs are planned. For NVZ farms, specific rules on closed periods, storage capacity and maximum N loading apply. See the nutrient management planning guide for the full NMP framework.
Wheat crops with high organic manure inputs often have elevated SNS — failing to account for this leads to excessive total N application, increased nitrous oxide emissions, potential NVZ non-compliance and agronomic problems (over-dense canopies, lodging risk). AHDB RB209 ↗ provides the SNS class definitions and N rate tables that form the basis of all UK NMPs.