Season

Maize dry matter forecast 2028: when will the crop be ready?

GDD accumulation is tracking above the 10-year average across the Midlands and East. Our regional dry matter forecast map and harvest timing guide.

Regional GDD accumulation and harvest forecast — end July 2028

RegionGDD to dateForecast harvestDM expectedComment
East Anglia 1,280 GDD Late Sept 32–35% Ahead of 10-yr average; early-drilled crops approaching target
East Midlands 1,210 GDD Early Oct 30–33% On track for good DM; 10 days ahead of 2027
West Midlands 1,140 GDD Mid Oct 28–32% Cooler and wetter — monitor carefully; late hybrids at risk
Yorkshire 1,090 GDD Mid-late Oct 28–31% Lower accumulated heat; prioritise early hybrids only
South West 1,180 GDD Early-mid Oct 29–33% Maritime influence — variable; check field-level data
South East 1,310 GDD Late Sept 33–36% Best conditions nationally; wholecrop and grain maize both on target

What 2028 GDD accumulation means for harvest planning

The warm, dry July that followed the wet June has significantly accelerated GDD accumulation relative to the 2027 season. Across eastern England, most crops drilled in late April or early May are now on track to reach target wholecrop DM (30–32%) by mid-to-late September — approximately 10–14 days earlier than 2027. Growers and contractors should begin DM assessment from early September rather than waiting for the traditional mid-September start.

The situation is more varied in northern and western regions: the cooler, wetter conditions that persisted longer in the West Midlands and Yorkshire mean that late-maturing hybrids (FAO 240+) in these regions may not reach 28% DM before the first serious frost risk in mid-October. Growers in these areas should prioritise their DM assessments and have contingency plans for harvesting at slightly below-target moisture if frost threatens. See the maize harvest management guide for the full decision framework.

GDD tracking: how to monitor your own crop

Track daily GDD accumulation from your nearest weather station using the formula: GDD/day = max(0, (Tmax + Tmin)/2 − 10). Cumulative GDD from drilling date provides the best harvest timing predictor for your specific location. Early-season hybrid FAO ratings and the hybrid supplier's GDD-to-harvest target allow you to calculate the remaining GDD required and therefore the approximate harvest date. See the growing degree days glossary entry and the maize establishment guide for hybrid selection considerations that affect GDD requirements.

Frequently asked questions

What dry matter percentage should I target for wholecrop and grain maize harvest?
The target dry matter (DM) differs by end use: Wholecrop silage — 28–35% DM is the target range. Below 28%, the crop is too wet: silage will be poorly fermented, anaerobic conditions in the clamp are compromised, and effluent production is high. Above 35% DM, fibre digestibility declines and the crop is harder to consolidate effectively in the clamp. The optimum for most contractors and farms is 30–32% DM. Grain maize — target harvest at 30–35% grain moisture (equivalent to approximately 65–70% DM in the grain). Grain maize requires drying to below 14% for safe storage, so harvest moisture directly determines drying cost. See the maize harvest management guide for the full DM assessment and combining decision framework.
How do I measure dry matter content in a standing maize crop?
There are three practical methods for assessing DM in standing maize: (1) Visual assessment — the crop is at approximately 30–35% DM when: the lower 3–4 leaves have dried and died; the ear husks are beginning to dry and pull away; the grain shows a visible dent (dent stage); and the cob is at approximately 90° to the stem. This gives a rough indication only. (2) Microwave DM test — chop a representative sample (include stem, leaf and cob in roughly the proportions in the whole crop), weigh it, microwave until weight stabilises, reweigh, and calculate DM%. This is the standard farm method. (3) Near-infrared (NIR) analysis — many feed advisers and forage laboratories offer on-farm NIR testing with a handheld device — this gives the most accurate simultaneous DM and quality analysis. Make assessments at multiple points in the field (at least 5 sites) as DM can vary significantly within a field. See the maize harvest management guide.
What is a GDD and how is it used to predict maize harvest date?
Growing degree days (GDD) measure the heat accumulation above maize's base temperature (10°C in UK practice): GDD/day = max(0, (Tmax + Tmin)/2 − 10). Maize hybrids are characterised by their FAO maturity number, which broadly corresponds to the GDD requirement from sowing to harvest maturity: early hybrids (FAO 180–220) require approximately 1,100–1,200 GDD from sowing to wholecrop target DM; late hybrids (FAO 250–300) require 1,300–1,450 GDD. By tracking cumulative GDD from drilling date, and forecasting future GDD accumulation from seasonal weather forecasts, the harvest date can be predicted with reasonable accuracy 3–4 weeks ahead. The AHDB maize GDD calculator ↗ provides a useful tool for UK farms. See the growing degree days glossary entry.
Should I alter my maize harvest plans given the 2028 forecast?
The 2028 GDD accumulation data (above 10-year average in most regions) suggests that most early-to-medium hybrids should be at or approaching target DM by mid-September in eastern England — approximately 10–14 days ahead of the 2027 season. The practical implications: (1) book the contractor early — contractors may reach capacity rapidly if all regional crops are ready simultaneously; (2) prepare clamp infrastructure ahead of schedule — push the previous year's silage back, check sheeting and tyres; (3) conduct DM assessments from early September rather than mid-September to avoid missing the optimal window; (4) in the West Midlands and Yorkshire, late hybrids should be monitored carefully — GDD accumulation is less advanced and these crops may not reach 28% DM before the first frost risk window. See the maize harvest management guide for the full harvest decision framework.
What happens to maize quality if harvest is delayed beyond the optimal DM window?
Once maize passes 35–38% DM (the upper end of the wholecrop window), quality deterioration accelerates through several mechanisms: (1) Starch digestibility declines — as grain dries, the starch vitrifies (becomes harder), reducing rumen digestibility in dairy and beef diets; (2) Fibre digestibility falls — stem lignification continues after the grain DM peak, reducing the digestibility of the structural carbohydrates; (3) Clamping difficulty — dry material is harder to consolidate, increasing the risk of aerobic spoilage (heating) once the clamp is opened; (4) Cob and husk losses increase — very late harvest at harvest increases combine header losses and reduces the cob fraction (the highest-quality part of the plant). For grain maize, higher moisture at harvest is preferable to very dry grain (above 32% moisture) which causes kernel shattering and increased harvest losses. See the harvest maturity glossary entry.