Growth · Potato

Hilling

Also: earthing up · ridging

Drawing soil up around plant stems, as with potatoes, to protect tubers from light.

Exposed potato tubers turn green and produce solanine, making them inedible. Hilling — also called earthing up or ridging — covers developing tubers, encourages stolon development and can improve drainage. It is done in one or two passes as the haulm grows, typically when plants reach 20–30 cm.

Hilling passes — timing and objectives

PassTimingAimRidge heightNotes
First hilling Plants 10–15 cm tall Cover base of stems, encourage stolon development 15–20 cm Usually done 3–4 weeks after emergence
Second hilling Plants 20–30 cm tall Cover developing tubers, create final ridge profile 25–35 cm Critical timing — before tubers become visible
Desiccation check Pre-harvest Confirm ridge height adequate for mechanical harvester ≥30 cm Low ridges increase bruising risk at harvest

Why tuber cover matters

Potato tubers develop from stolons (horizontal underground stems) that grow from the base of the plant's stems. Tubers are modified stem tissue — they are not roots, and they do not develop from the seed piece itself. When stolons grow into the ridge of mounded soil, they initiate tubers within that zone. Inadequate ridge depth leaves tubers closer to the surface, where light penetration causes greening and solanine accumulation.

The AHDB potato agronomy knowledge library ↗ provides the full context on stolon development, tuber initiation and ridge management. The potato agronomy guide covers hilling in the context of the complete crop management sequence from seed to store.

Hilling equipment and ridge profiles

Hilling is typically done with a ridging body fitted to a standard bed-former or inter-row cultivator. The ridge profile should be symmetrical, with sufficient height to cover tubers and a cross-section that resists slumping. In the UK, standard bed centres are 75–90 cm. Well-formed ridges have a trapezoidal cross-section — a flat crest rather than a sharp peak, which reduces the risk of the ridge top being washed or cultivated away. After heavy rain, check ridge height and re-hill if significant slumping has occurred.

Mechanical potato harvesters require consistent ridge geometry to operate efficiently — irregular ridges (variable height or width) increase bruising rates during lifting. Before harvest, assess ridge height across the field at multiple points. The soil compaction entry covers why soil structural quality affects both hilling ease and ridge stability.

Hilling and slug management

Ridge height interacts with slug pressure — tubers closer to the surface are more accessible to slugs moving through the ridge. Well-ridged crops with consistent height of ≥30 cm reduce slug access to developing tubers compared to low ridges. This is particularly important in fields with known slug pressure from previous crops (cover crops, oil seed rape, cereals after wet harvest). For slug management in potato crops, see the slug management guide, and for potato agronomy context, the potato agronomy guide.

Frequently asked questions

Why do exposed potato tubers turn green?
Potato tubers exposed to light produce chlorophyll (turning green) and solanine — a toxic glycoalkaloid. Solanine concentration increases with continued light exposure and is concentrated beneath the green skin. Greening begins within a few hours of light exposure. UK food safety regulations set a maximum solanine level of 200 mg/kg for marketed potatoes; heavily greened tubers should be rejected. AHDB ↗ and the Food Standards Agency ↗ provide guidance on greening risk and consumer safety. Thorough hilling combined with good ridge maintenance is the primary prevention measure.
When should the first hilling pass be done?
The first hilling pass should be done when plants are 10–15 cm tall — typically 3–4 weeks after emergence. At this stage, stolons are actively developing but tuber initiation has not yet started, so covering the base of stems encourages more stolon development and therefore more tuber sites. Hilling too early risks burying the emerging stems; too late risks exposing early tuber initials. AHDB potato agronomy guidance ↗ gives timing recommendations by variety type and seed rate. See the potato agronomy guide for the full crop management sequence.
How high should ridges be at the end of hilling?
Final ridge height should be at least 25–35 cm from the base of the furrow to the ridge crest, with a well-shaped profile that resists soil slumping. Low ridges (<20 cm) leave developing tubers inadequately covered and increase greening and slug damage risk. Ridge height also affects mechanical harvester performance — low ridges can reduce lifting efficiency and increase bruising. AHDB potato production guidance ↗ recommends ridge cross-section and height specifications. On sandy or light soils, ridges may slump after heavy rain and require re-hilling.
Does hilling help with weed control?
Yes — hilling buries emerged weeds in the inter-row zone, providing effective mechanical weed control without herbicides. Weeds buried by hilling are killed by soil coverage. The most effective timing is when weeds are at the white thread / cotyledon stage — before they are well established. A single hilling pass at this timing can eliminate 80–90% of inter-row annual weeds. However, hilling cannot control weeds within the row (directly under the crop canopy). Post-emergence herbicides are still needed for within-row weeds in most situations. See the weed management guide for integrated weed management principles more broadly.
Can hilling be done in wet conditions?
Hilling in wet soil conditions should be avoided where possible. Working soil when it is too wet causes soil structural damage — compaction and surface capping. Potato ridges formed from wet soil slump as they dry, losing their shape and effective cover depth. On heavy clay soils, wet conditions also risk creating soil clods that increase tuber bruising at harvest. The general guidance is to hill when soil conditions allow cultivation without smearing — similar to the conditions required for seedbed cultivation. AHDB soil management for potatoes ↗ covers soil conditions for all cultivation operations. The soil compaction glossary entry explains the structural consequences of working wet soils.