Wheat grain quality parameters
Step-by-step wheat harvest management
- 1
Assess crop maturity and optimum harvest timing
The ideal combining window for wheat begins when grain moisture falls below 20% (typical in UK conditions: late July–mid August for winter wheat) and when all green colour has disappeared from the ear and upper leaf. A simple test: squeeze 20 grains from across the field — if all are hard with no "squash" and no green tinge, the crop is physiologically mature. Waiting until moisture is below 18% avoids high fuel costs from excessive artificial drying. Do not delay beyond 15–16% moisture unless drying capacity allows — the risk of weather damage (rain-induced HFN fall, mycotoxin accumulation in Fusarium years) increases rapidly after physiological maturity. In high Fusarium ear blight (FEB) risk years, earlier harvest at higher moisture is preferable to leaving grain on the plant — harvest and dry rather than leave standing. Use weather forecasts and crop monitoring to plan logistics 7–10 days ahead.
- 2
Set the combine correctly for wheat
Combine settings for wheat differ from barley and oilseed rape — incorrect settings cause grain damage, excessive losses or impurity. Key settings: drum/rotor speed for wheat: typically 900–1,100 rpm for conventional cylinders; reduce for thin, lightweight grain to avoid cracking. Concave clearance: 6–10 mm at entry, 2–5 mm at exit for conventional; adjust for grain size and moisture. Fan speed: set to separate chaff without blowing grain into the tailings — typically 6.0–8.5 m/s; reduce for lightweight grain. Sieve settings: top sieve 11–13 mm; bottom sieve 8–10 mm for wheat. Losses from the combine should not exceed 1–1.5% of yield — conduct daily loss assessments by laying a drop cloth behind the combine and counting grains. In wet conditions, increase cleaning fan speed and reduce throughput. Adjust settings when moving between fields with different moisture or crop conditions.
- 3
Monitor grain quality continuously during harvest
Grain quality can change significantly between fields, parts of the field, or through the day as morning dew raises moisture on a standing crop. Take representative combine samples every 2–3 hours of operation: test moisture with a calibrated moisture meter; assess specific weight with a 1-litre test weight cup; visually inspect for screenings, sprouting, discolouration or mould. For milling wheat: manage specific weight lots carefully — thin grain at field corners or headlands can contaminate an otherwise acceptable bulk. Where Hagberg Falling Number is a risk (wet harvest year, susceptible variety), test HFN from combine samples — a fall to below 220 seconds is a commercial disaster for milling contracts and requires immediate segregation. Keep field-by-field records of combine sample quality to inform store segregation decisions.
- 4
Manage grain drying to target moisture
Grain entering long-term storage must be at or below 14% moisture — at 14.5%, biological activity begins to accelerate and storage life reduces significantly. Continuous-flow driers (tower driers) handle high throughput but require careful temperature management — maximum grain temperature for milling wheat: 60°C (avoid starch damage and HFN reduction). Batch driers allow precise control and are preferred for malting quality parcels. Ambient air drying (floor stores with ducted ventilation) works for grain arriving at 15–16% moisture in favourable autumn conditions but is not suitable for grain above 17% moisture. Energy efficiency: each percentage point of moisture removed per tonne costs approximately 0.5–0.8 litres of diesel at current fuel prices. Blend moisture-uniform grain after drying — do not blend wet and dry grain. Keep accurate drying records: moisture in, moisture out, temperature settings, fuel used — essential for energy cost accounting and carbon reporting.
- 5
Segregate and intake grain into store correctly
Grain intake management at the store determines whether quality is maintained or lost. Segregate by: (1) variety — especially for milling wheat where breadmaking quality differs by variety; (2) quality — specific weight, protein, moisture class; (3) risk — Fusarium-affected grain or grain with elevated DON must be segregated immediately and tested before any movement. Test representative intake samples at the weighbridge: moisture, specific weight, screenings as a minimum; protein and HFN for milling consignments. Set intake rejections clearly before harvest starts — define the moisture and specific weight thresholds below which grain goes to a separate low-grade bay rather than the main store. Ensure stores are clean, cool and dry before filling — clean out previous season's grain residue and spray with approved grain store pesticide. See the <a href="/news/fusarium-ear-blight-outlook-2029">FEB outlook 2029 article</a> for mycotoxin testing obligations and DON risk management in high-risk years.
Planning for quality and compliance
Wheat harvest management is no longer just a logistical exercise — quality, traceability and food safety compliance are now central requirements for all grain sold into the milling supply chain. The Red Tractor Combinable Crops standard and individual merchant contracts increasingly require: mycotoxin test certificates for milling consignments; grain store treatment records; accurate field-by-field yield and quality data; and traceability from field to store to merchant. Build these records as harvest progresses — retrospective reconstruction is time-consuming and error-prone.
The harvest index entry covers the yield component context; the grain protein entry covers protein management for milling quality; the FEB 2029 outlook article provides mycotoxin risk guidance for the current season. For storage decisions see the grain storage management guide.