Top story Season

Winter Wheat Drilling Window

Winter Wheat Drilling Window.

Why the drilling window matters

Winter wheat has an optimum drilling window — typically late September through to late October in Northern Europe, depending on variety and location. Within this window, the crop has enough time to establish a healthy root system before winter temperatures slow growth. Outside it, yield potential drops measurably.

Research published by AHDB Cereals & Oilseeds suggests that each week of delay past the optimal window costs roughly 0.1–0.2 t/ha. Waiting for the perfect seedbed is worth it — drilling into poor conditions and then waiting for rain can cost more than a week's delay would have.

Three checks before the drill goes out

1. Soil moisture and structure

The seedbed needs to be firm enough for seed-to-soil contact and moist enough to start germination. Squeeze a handful of topsoil at seeding depth: it should crumble apart, not form a ribbon (too wet) or turn to dust (too dry). The SARE Winter Wheat guide recommends drilling at 1–1.5 inches depth to ensure seeds contact consistent moisture. In a dry seedbed, go slightly deeper.

Walk the field in at least four locations before you start — soil condition varies more than you expect across a single farm.

2. Seed lot data: germination and TGW

Your seed rate calculation depends on two figures from the seed label: germination percentage and thousand-grain weight (TGW). Neither can be borrowed from last year. Both change between lots and between seasons — TGW alone can vary by 10–15 % in a single variety across seasons.

If TGW is not printed on the label, ask your merchant for the lot-specific technical data sheet. Alternatively, count and weigh three or four replicates of 100 seeds each, multiply by 10, and average. More on this in the TGW glossary entry.

KWS Sowing Wheat guidance and Bayer Crop Science's seeder calibration article both note that using a stale TGW figure is one of the most common reasons for plant populations falling outside the target range.

3. Drill calibration

Run a calibration check before the season begins, not after. Seed rate errors of ±10 % are common on unchecked drills — at higher seed rates this is costly, at lower rates it reduces yield potential. The Mississippi State Extension planting guide covers calibration procedure for common drill types.

Seed rate formula

Once you have your TGW and germination figures:

seed rate (kg/ha) = target plants/m² × TGW (g)
                   ÷ 100 ÷ germination % ÷ field emergence %

For a typical wheat target of 330 plants/m² with TGW of 45 g, 94 % germination and 85 % field emergence:

330 × 45 ÷ 100 ÷ 0.94 ÷ 0.85 ≈ 186 kg/ha

Use the interactive calculator on the TGW page to try your own figures.

What to check on day one

After drilling the first field or field section, stop and dig. Pull 10–15 seeds from different points across the tramline and check:

  • Seed depth is consistent and matches the target (typically 2–4 cm)
  • Seeds have soil contact — no air pockets around the seed
  • The coulter has not smeared the furrow sides in wetter conditions

Bayer's guide to establishing and assessing wheat stands covers what to look for at emergence and how to decide whether a re-drill is warranted.

Timing and the 2026 season context

The 2026 autumn drilling window across Northern Europe opened with variable conditions. An AHDB crop condition report noted that soils entered the window very dry and hard after a dry August — enabling good machinery access but limiting available seedbed moisture. September rainfall improved conditions significantly before the main drilling rush.

Keep monitoring — soil conditions at field scale can change within days of significant rain.

FAQ

Frequently asked questions

What soil moisture level is ideal for wheat drilling?
A seedbed that is firm enough for good seed-to-soil contact and moist enough to trigger rapid, uniform germination. If soils are very dry, consider increasing seeding depth to 1–1.5 inches to chase moisture; if waterlogged, wait — drilling into saturated soil destroys structure and reduces establishment. See AHDB guidance on soil moisture deficit.
How do I check whether my seedbed is ready?
Squeeze a handful of topsoil — it should crumble apart rather than forming a ribbon (too wet) or falling apart as dust (too dry). Walk the field in several locations; soil condition can vary significantly across a single field. Use a penetrometer if you have one: aim for <2 MPa in the top 15 cm.
Should I use the TGW from last year's label?
No. TGW changes between seasons and between seed lots. Always get the figure for the specific lot you are drilling. If it is not on the label, ask your merchant for the technical data sheet or measure it yourself — count 100 seeds, weigh them, multiply by 10, and repeat three times. Learn more in the TGW glossary entry.
What germination percentage should I use in my seed rate calculation?
Use the germination percentage from the seed certificate for the specific lot. Certified seed in the EU and UK must meet minimum germination standards (85 % for most cereals), but many lots will be higher. Do not default to 85 % if the label shows 94 % — you will over-order seed. Use our seed rate calculator with the actual lot figures.
How much does late drilling reduce yield?
Research from AHDB and NIAB suggests that for winter wheat in the UK, yield potential drops by roughly 0.1–0.2 t/ha for each week of delay past the optimum drilling window (typically late September to late October depending on variety). Later drilling also increases disease pressure in some varieties.
What is the recommended winter wheat drilling depth in the UK?
The standard winter wheat drilling depth is 25–40 mm (1–1.5 inches) under normal conditions. Drill shallower (25 mm) in moist seedbeds where moisture is at the surface, and deeper (40–50 mm) in dry conditions to place the seed into available moisture. Very shallow drilling (<20 mm) risks desiccation in dry autumns and exposure to surface-feeding birds and pests. Very deep drilling (>60 mm) weakens emergence energy, particularly for small-seeded varieties with lower TGW. The AHDB wheat establishment guide ↗ and FarmTheGuide wheat establishment guide cover drilling depth in detail alongside seed rate and variety choice.
Can I drill into a dry seedbed and rely on rain to finish germination?
It is possible but risky. If a dry spell follows, seeds can desiccate at shallow depths. If drilling dry, go slightly deeper (1.5 inches), increase seed rate slightly to account for poorer establishment, and monitor the forecast closely. Drilling into moisture is always the lower-risk option. Track current UK soil moisture via the Met Office farming weather pages.